{"title":"Orbot","description":"\u003cp\u003eAn orbital machine is mechanically simple and that is its advantage. There is no brush belt to slip and no cylinder to true up, so when one stops earning it is almost always a small part — a latch that will not hold, a spray jet washer that has perished, a grubscrew that has backed out of the drive gear.\u003c\/p\u003e\n\u003cp\u003eNone of those justify a service call, and none of them should keep a machine off the floor for a fortnight.\u003c\/p\u003e\n\u003cp\u003eThis range is the Orbot spares counter. It covers the pull latch assembly and its nuts, bolts, nylon washers and socket screws; the drive gear micro and its tee nuts; the damper spray cage and rubber washers for the spray jets; motor fan cover, motor lid and grounding terminal screws; the terminal strip, grommet, wheel axle and rear handle screws for the Micro.\u003c\/p\u003e\n\u003ch2\u003eHow to choose\u003c\/h2\u003e\n\u003cp\u003e\u003cstrong\u003eOrder by the assembly, not the fastener.\u003c\/strong\u003e Several of these are ordinary-looking screws and nuts that are specific to one point on the machine — the pull latch rod, the mounting driver plate, the fan motor cover. The product title names the location. Match that rather than the thread size.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eLatch parts are sold as a retro kit for a reason.\u003c\/strong\u003e The Orbot Latch (Retro Kit of 2) replaces both sides. Replacing one and leaving the other usually means doing the job twice, because they wear at the same rate.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eSpray jet washers are consumables.\u003c\/strong\u003e A machine that has started to dribble or spray unevenly is far more often a perished rubber washer than a blocked jet. They cost cents and are worth holding.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eCheck the grubscrew before condemning the drive gear.\u003c\/strong\u003e A drive gear that slips under load is usually a hex grubscrew that has worked loose against the counterweight, not a failed gear.\u003c\/p\u003e\n\u003cp\u003ePads and bonnets for orbital work are in \u003ca href=\"\/collections\/floor-pads\"\u003eFloor Pads\u003c\/a\u003e and \u003ca href=\"\/collections\/carpet-bonnets\"\u003eCarpet Bonnets\u003c\/a\u003e, the chemistry that runs with them is in \u003ca href=\"\/collections\/encapsulation-bonnet-cleaning\"\u003eEncapsulation \u0026amp; Bonnet Cleaning\u003c\/a\u003e, and general machine spares are in \u003ca href=\"\/collections\/parts-maintenance\"\u003eParts \u0026amp; Maintenance\u003c\/a\u003e.\u003c\/p\u003e","products":[{"product_id":"orbot-wheel-axle","title":"Orbot Wheel Axle","description":"\u003ch2\u003eOrbot wheel axle\u003c\/h2\u003e\n\u003cp\u003eThe axle that carries a transport wheel on an Orbot orbital floor machine.\u003c\/p\u003e\n\u003ch2\u003eWhy an axle wears\u003c\/h2\u003e\u003cp\u003eAn orbital machine is heavy and it is wheeled in and out of vehicles and over thresholds all day. The axle and its bearing surfaces take that load, and a worn axle shows up as a wheel that wobbles or sits out of line — which then drags on the machine and makes it harder to steer.\u003c\/p\u003e\n\u003ch2\u003eIdentifying the right part\u003c\/h2\u003e\u003cp\u003eFasteners and small components change between production runs, and the part on your machine may not match the current drawing. Measure what you are replacing, or photograph it against a ruler, and send that with your model and serial number. It takes a minute and it saves an order that does not fit.\u003c\/p\u003e\n\u003chr\u003e\n\u003cp\u003eOrbot part numbers are not always obvious from the machine. Send us the model, the serial number and a photograph of the part you need and we will confirm it before you order.\u003c\/p\u003e","brand":"Orbot","offers":[{"title":"EACH","offer_id":43851476893909,"sku":"HOS4002","price":29.78,"currency_code":"AUD","in_stock":true}]},{"product_id":"orbot-washer-0-5inch-nylon-pull-latch-r","title":"Orbot Washer 0.5inch Nylon Pull Latch R","description":"\u003ch2\u003eOrbot nylon washer, 1\/2 inch, for the pull latch rod\u003c\/h2\u003e\n\u003cp\u003eThe nylon washer from the pull latch assembly on an Orbot machine.\u003c\/p\u003e\n\u003ch2\u003ePart of a small assembly\u003c\/h2\u003e\u003cp\u003eThe pull latch is made up of a rod, a \u003ca href=\"\/products\/orbot-nut-0-5inch-pull-latch-rod\"\u003enut\u003c\/a\u003e, a \u003ca href=\"\/products\/orbot-bolt-0-5inch-pull-latch-rod\"\u003ebolt\u003c\/a\u003e and this washer. If the latch has gone loose or will not hold, replace the group rather than one piece — the parts wear together.\u003c\/p\u003e\n\u003ch2\u003eIdentifying the right part\u003c\/h2\u003e\u003cp\u003eFasteners and small components change between production runs, and the part on your machine may not match the current drawing. Measure what you are replacing, or photograph it against a ruler, and send that with your model and serial number. It takes a minute and it saves an order that does not fit.\u003c\/p\u003e\n\u003chr\u003e\n\u003cp\u003eOrbot part numbers are not always obvious from the machine. Send us the model, the serial number and a photograph of the part you need and we will confirm it before you order.\u003c\/p\u003e","brand":"Orbot","offers":[{"title":"EACH","offer_id":43851477450965,"sku":"HOS1029","price":1.77,"currency_code":"AUD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/2179\/6391\/products\/Orbot-Washer-0_5inch-Nylon-Pull-Latch-R.jpg?v=1780551460"},{"product_id":"orbot-rubber-washer-for-spray-jets","title":"Orbot Rubber Washer for Spray Jets","description":"\u003ch2\u003eOrbot rubber washer for spray jets\u003c\/h2\u003e\n\u003cp\u003eThe sealing washer behind a spray jet on an Orbot machine.\u003c\/p\u003e\n\u003ch2\u003eThe usual cause of a dripping jet\u003c\/h2\u003e\u003cp\u003eWhen solution weeps from around a jet rather than out of it, the washer behind it has hardened or split. It is a cheap part and a five-minute job, and leaving it means solution running down the inside of the head where you cannot see what it is doing.\u003c\/p\u003e\n\u003ch2\u003eIdentifying the right part\u003c\/h2\u003e\u003cp\u003eFasteners and small components change between production runs, and the part on your machine may not match the current drawing. Measure what you are replacing, or photograph it against a ruler, and send that with your model and serial number. It takes a minute and it saves an order that does not fit.\u003c\/p\u003e\n\u003chr\u003e\n\u003cp\u003eOrbot part numbers are not always obvious from the machine. Send us the model, the serial number and a photograph of the part you need and we will confirm it before you order.\u003c\/p\u003e","brand":"Orbot","offers":[{"title":"EACH","offer_id":43851477811413,"sku":"HOS3013","price":0.55,"currency_code":"AUD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/2179\/6391\/products\/Orbot-Rubber-Washer-for-Spray-Jets.jpg?v=1780551460"},{"product_id":"orbot-terminal-strip","title":"Orbot Terminal Strip","description":"\u003ch2\u003eOrbot terminal strip\u003c\/h2\u003e\n\u003cp\u003eThe electrical terminal strip from an Orbot machine.\u003c\/p\u003e\n\u003ch2\u003eElectrical work is not a field repair\u003c\/h2\u003e\u003cp\u003eA terminal strip is inside the machine and carries mains voltage. In Australia, work on the electrical side of a 230 V appliance is licensed work. Order the part if you have a qualified person doing the job; if you do not, send the machine in rather than open it.\u003c\/p\u003e\n\u003ch2\u003eIdentifying the right part\u003c\/h2\u003e\u003cp\u003eFasteners and small components change between production runs, and the part on your machine may not match the current drawing. Measure what you are replacing, or photograph it against a ruler, and send that with your model and serial number. It takes a minute and it saves an order that does not fit.\u003c\/p\u003e\n\u003chr\u003e\n\u003cp\u003eOrbot part numbers are not always obvious from the machine. Send us the model, the serial number and a photograph of the part you need and we will confirm it before you order.\u003c\/p\u003e","brand":"Orbot","offers":[{"title":"EACH","offer_id":43851477876949,"sku":"HOS1009","price":2.53,"currency_code":"AUD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/2179\/6391\/products\/Orbot-Terminal-Strip.jpg?v=1780551461"},{"product_id":"orbot-screw-socket-new-latch","title":"Orbot Screw Socket New Latch","description":"\u003ch2\u003eOrbot socket screw for the new-style latch\u003c\/h2\u003e\n\u003cp\u003eThe socket screw used with the later latch assembly on an Orbot machine.\u003c\/p\u003e\n\u003ch2\u003eNew style or old style?\u003c\/h2\u003e\u003cp\u003eOrbot changed the latch design, and the fasteners changed with it. This screw is for the \u003cstrong\u003enew style\u003c\/strong\u003e latch. If you are retro-fitting the newer latch to an older machine, the \u003ca href=\"\/products\/orbot-latch-retro-kit-of-2\"\u003elatch retro kit of two\u003c\/a\u003e is the part to look at.\u003c\/p\u003e\n\u003ch2\u003eIdentifying the right part\u003c\/h2\u003e\u003cp\u003eFasteners and small components change between production runs, and the part on your machine may not match the current drawing. Measure what you are replacing, or photograph it against a ruler, and send that with your model and serial number. It takes a minute and it saves an order that does not fit.\u003c\/p\u003e\n\u003chr\u003e\n\u003cp\u003eOrbot part numbers are not always obvious from the machine. Send us the model, the serial number and a photograph of the part you need and we will confirm it before you order.\u003c\/p\u003e","brand":"Orbot","offers":[{"title":"EACH","offer_id":43851478434005,"sku":"HOS1003-09","price":0.41,"currency_code":"AUD","in_stock":true}]},{"product_id":"orbot-screw-rear-handle-for-micro","title":"Orbot Screw Rear Handle for Micro","description":"\u003ch2\u003eOrbot Micro rear handle screw\u003c\/h2\u003e\n\u003cp\u003eThe screw that secures the rear handle on the Orbot Micro.\u003c\/p\u003e\n\u003ch2\u003eMicro-specific\u003c\/h2\u003e\u003cp\u003eThis fastener is for the \u003cstrong\u003eOrbot Micro\u003c\/strong\u003e, not the full-size machines. The Micro shares very little hardware with the larger units.\u003c\/p\u003e\n\u003ch2\u003eIdentifying the right part\u003c\/h2\u003e\u003cp\u003eFasteners and small components change between production runs, and the part on your machine may not match the current drawing. Measure what you are replacing, or photograph it against a ruler, and send that with your model and serial number. It takes a minute and it saves an order that does not fit.\u003c\/p\u003e\n\u003chr\u003e\n\u003cp\u003eOrbot part numbers are not always obvious from the machine. Send us the model, the serial number and a photograph of the part you need and we will confirm it before you order.\u003c\/p\u003e","brand":"Orbot","offers":[{"title":"EACH","offer_id":43851478630613,"sku":"HOSOM-24","price":0.31,"currency_code":"AUD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/2179\/6391\/files\/Orbot-Screw-Rear-Handle-for-Micro.jpg?v=1780551462"},{"product_id":"orbot-screw-mounting-driver-plate","title":"Orbot Screw Mounting Driver Plate","description":"\u003ch2\u003eOrbot driver plate mounting screw\u003c\/h2\u003e\n\u003cp\u003eThe screw that mounts the driver plate on an Orbot orbital machine.\u003c\/p\u003e\n\u003ch2\u003eCheck these when a machine starts to vibrate\u003c\/h2\u003e\u003cp\u003eThe driver plate is the part that carries the pad and takes the orbital load. A mounting screw that has backed off changes the balance of the head, and the first symptom is vibration through the handles rather than an obvious fault. Check them as part of routine service.\u003c\/p\u003e\n\u003ch2\u003eIdentifying the right part\u003c\/h2\u003e\u003cp\u003eFasteners and small components change between production runs, and the part on your machine may not match the current drawing. Measure what you are replacing, or photograph it against a ruler, and send that with your model and serial number. It takes a minute and it saves an order that does not fit.\u003c\/p\u003e\n\u003chr\u003e\n\u003cp\u003eOrbot part numbers are not always obvious from the machine. Send us the model, the serial number and a photograph of the part you need and we will confirm it before you order.\u003c\/p\u003e","brand":"Orbot","offers":[{"title":"EACH","offer_id":43851478663381,"sku":"HOS3047","price":0.18,"currency_code":"AUD","in_stock":true}]},{"product_id":"orbot-screw-motor-lid","title":"Orbot Screw Motor Lid","description":"\u003ch2\u003eOrbot motor lid screw\u003c\/h2\u003e\n\u003cp\u003eThe screw that secures the motor lid on an Orbot machine.\u003c\/p\u003e\n\u003ch2\u003eIdentifying the right part\u003c\/h2\u003e\u003cp\u003eFasteners and small components change between production runs, and the part on your machine may not match the current drawing. Measure what you are replacing, or photograph it against a ruler, and send that with your model and serial number. It takes a minute and it saves an order that does not fit.\u003c\/p\u003e\n\u003chr\u003e\n\u003cp\u003eOrbot part numbers are not always obvious from the machine. Send us the model, the serial number and a photograph of the part you need and we will confirm it before you order.\u003c\/p\u003e","brand":"Orbot","offers":[{"title":"EACH","offer_id":43851478859989,"sku":"HOS3023-06","price":0.55,"currency_code":"AUD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/2179\/6391\/products\/Orbot-Screw-Motor-Lid.jpg?v=1780551462"},{"product_id":"orbot-screw-fan-motor-cover","title":"Orbot Screw Fan Motor Cover","description":"\u003ch2\u003eOrbot fan motor cover screw\u003c\/h2\u003e\n\u003cp\u003eThe screw that secures the fan motor cover on an Orbot machine.\u003c\/p\u003e\n\u003ch2\u003eMatching part\u003c\/h2\u003e\u003cp\u003eThe cover itself is the \u003ca href=\"\/products\/orbot-motor-fan-cover\"\u003eOrbot motor fan cover\u003c\/a\u003e.\u003c\/p\u003e\n\u003ch2\u003eIdentifying the right part\u003c\/h2\u003e\u003cp\u003eFasteners and small components change between production runs, and the part on your machine may not match the current drawing. Measure what you are replacing, or photograph it against a ruler, and send that with your model and serial number. It takes a minute and it saves an order that does not fit.\u003c\/p\u003e\n\u003chr\u003e\n\u003cp\u003eOrbot part numbers are not always obvious from the machine. Send us the model, the serial number and a photograph of the part you need and we will confirm it before you order.\u003c\/p\u003e","brand":"Orbot","offers":[{"title":"EACH","offer_id":43851479220437,"sku":"HOS3023-05","price":1.0,"currency_code":"AUD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/2179\/6391\/products\/Orbot-Screw-Fan-Motor-Cover.jpg?v=1780551464"},{"product_id":"orbot-screw-grounding-terminal-box","title":"Orbot Screw Grounding Terminal Box","description":"\u003ch2\u003eOrbot grounding terminal box screw\u003c\/h2\u003e\n\u003cp\u003eThe screw that secures the earth connection in the terminal box of an Orbot machine.\u003c\/p\u003e\n\u003ch2\u003eThis one is a safety part\u003c\/h2\u003e\u003cp\u003eIt is a screw, and it is the screw that holds the earth. A loose or missing earth connection on a 230 V machine is not a cosmetic fault. If this screw is missing, do not run the machine until it has been replaced and the earth continuity checked by a qualified person.\u003c\/p\u003e\n\u003ch2\u003eIdentifying the right part\u003c\/h2\u003e\u003cp\u003eFasteners and small components change between production runs, and the part on your machine may not match the current drawing. Measure what you are replacing, or photograph it against a ruler, and send that with your model and serial number. It takes a minute and it saves an order that does not fit.\u003c\/p\u003e\n\u003chr\u003e\n\u003cp\u003eOrbot part numbers are not always obvious from the machine. Send us the model, the serial number and a photograph of the part you need and we will confirm it before you order.\u003c\/p\u003e","brand":"Orbot","offers":[{"title":"EACH","offer_id":43851479417045,"sku":"HOS1032","price":0.55,"currency_code":"AUD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/2179\/6391\/products\/Orbot-Screw-Grounding-Terminal-Box.jpg?v=1780551463"},{"product_id":"orbot-quick-connect-tee","title":"Orbot Quick Connect Tee","description":"\u003ch2\u003eOrbot quick connect tee\u003c\/h2\u003e\n\u003cp\u003eThe tee fitting that splits the solution line on an Orbot machine.\u003c\/p\u003e\n\u003ch2\u003eWhere it sits\u003c\/h2\u003e\u003cp\u003eThe tee divides solution between jets. A cracked tee shows up as uneven spray across the head — one side wetter than the other — rather than as an obvious leak, because the loss is inside the housing.\u003c\/p\u003e\n\u003ch2\u003eIdentifying the right part\u003c\/h2\u003e\u003cp\u003eFasteners and small components change between production runs, and the part on your machine may not match the current drawing. Measure what you are replacing, or photograph it against a ruler, and send that with your model and serial number. It takes a minute and it saves an order that does not fit.\u003c\/p\u003e\n\u003chr\u003e\n\u003cp\u003eOrbot part numbers are not always obvious from the machine. Send us the model, the serial number and a photograph of the part you need and we will confirm it before you order.\u003c\/p\u003e","brand":"Orbot","offers":[{"title":"EACH","offer_id":43851479646421,"sku":"HOS3019","price":13.2,"currency_code":"AUD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/2179\/6391\/products\/Orbot-Quick-Connect-Tee.jpg?v=1780551464"},{"product_id":"orbot-nut-0-5inch-pull-latch-rod","title":"Orbot Nut 0.5inch Pull Latch Rod","description":"\u003ch2\u003eOrbot nut, 1\/2 inch, for the pull latch rod\u003c\/h2\u003e\n\u003cp\u003eThe nut from the pull latch rod assembly on an Orbot machine.\u003c\/p\u003e\n\u003ch2\u003ePart of a small assembly\u003c\/h2\u003e\u003cp\u003eThe latch group is a rod, this nut, a \u003ca href=\"\/products\/orbot-bolt-0-5inch-pull-latch-rod\"\u003ebolt\u003c\/a\u003e and a \u003ca href=\"\/products\/orbot-washer-0-5inch-nylon-pull-latch-r\"\u003enylon washer\u003c\/a\u003e. A latch that will not hold adjustment usually needs more than one of them.\u003c\/p\u003e\n\u003ch2\u003eIdentifying the right part\u003c\/h2\u003e\u003cp\u003eFasteners and small components change between production runs, and the part on your machine may not match the current drawing. Measure what you are replacing, or photograph it against a ruler, and send that with your model and serial number. It takes a minute and it saves an order that does not fit.\u003c\/p\u003e\n\u003chr\u003e\n\u003cp\u003eOrbot part numbers are not always obvious from the machine. Send us the model, the serial number and a photograph of the part you need and we will confirm it before you order.\u003c\/p\u003e","brand":"Orbot","offers":[{"title":"EACH","offer_id":43851479679189,"sku":"HOS1030","price":0.77,"currency_code":"AUD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/2179\/6391\/products\/Orbot-Nut-0_5inch-Pull-Latch-Rod.jpg?v=1780551464"},{"product_id":"orbot-nut-tee-for-drivers","title":"Orbot Nut Tee for Drivers","description":"\u003ch2\u003eOrbot tee nut for drivers\u003c\/h2\u003e\n\u003cp\u003eThe tee nut used in the driver assembly of an Orbot machine.\u003c\/p\u003e\n\u003ch2\u003ePart of the driver assembly\u003c\/h2\u003e\u003cp\u003eFitted with the \u003ca href=\"\/products\/orbot-screw-mounting-driver-plate\"\u003edriver plate mounting screw\u003c\/a\u003e. Tee nuts pull through their seating when repeatedly over-torqued — if a screw will not tighten, the nut is usually the reason rather than the screw.\u003c\/p\u003e\n\u003ch2\u003eIdentifying the right part\u003c\/h2\u003e\u003cp\u003eFasteners and small components change between production runs, and the part on your machine may not match the current drawing. Measure what you are replacing, or photograph it against a ruler, and send that with your model and serial number. It takes a minute and it saves an order that does not fit.\u003c\/p\u003e\n\u003chr\u003e\n\u003cp\u003eOrbot part numbers are not always obvious from the machine. Send us the model, the serial number and a photograph of the part you need and we will confirm it before you order.\u003c\/p\u003e","brand":"Orbot","offers":[{"title":"EACH","offer_id":43851479875797,"sku":"HOS3043","price":0.33,"currency_code":"AUD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/2179\/6391\/products\/Orbot-Nut-Tee-for-Drivers.jpg?v=1780551465"},{"product_id":"orbot-motor-fan-cover","title":"Orbot Motor Fan Cover","description":"\u003ch2\u003eOrbot motor fan cover\u003c\/h2\u003e\n\u003cp\u003eThe cover over the motor cooling fan on an Orbot machine.\u003c\/p\u003e\n\u003ch2\u003eDo not run the machine without it\u003c\/h2\u003e\u003cp\u003eThe cover guards a spinning fan and directs cooling air across the motor. Running without it exposes the fan and changes the airflow the motor relies on to stay within temperature. A machine that keeps cutting out on thermal overload is worth checking for a missing or crushed cover before anything more expensive is suspected.\u003c\/p\u003e\u003cp\u003eThe matching fastener is the \u003ca href=\"\/products\/orbot-screw-fan-motor-cover\"\u003efan motor cover screw\u003c\/a\u003e.\u003c\/p\u003e\n\u003ch2\u003eIdentifying the right part\u003c\/h2\u003e\u003cp\u003eFasteners and small components change between production runs, and the part on your machine may not match the current drawing. Measure what you are replacing, or photograph it against a ruler, and send that with your model and serial number. It takes a minute and it saves an order that does not fit.\u003c\/p\u003e\n\u003chr\u003e\n\u003cp\u003eOrbot part numbers are not always obvious from the machine. Send us the model, the serial number and a photograph of the part you need and we will confirm it before you order.\u003c\/p\u003e","brand":"Orbot","offers":[{"title":"EACH","offer_id":43851480072405,"sku":"HOS3023-04","price":65.51,"currency_code":"AUD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/2179\/6391\/products\/Orbot-Motor-Fan-Cover.jpg?v=1780551466"},{"product_id":"orbot-latch-retro-kit-of-2","title":"Orbot Latch (Retro Kit of 2)","description":"\u003ch2\u003eOrbot latch, retro kit of two\u003c\/h2\u003e\n\u003cp\u003eA pair of latches supplied as a retro-fit kit, for updating an Orbot machine to the later latch design.\u003c\/p\u003e\n\u003ch2\u003eWhy retro-fit a latch\u003c\/h2\u003e\u003cp\u003eLatches take a knock every time the machine is loaded, and the later design was introduced because the earlier one was the weak point. Supplied as a pair so both sides match — fitting one new and leaving one old gives you uneven clamping.\u003c\/p\u003e\u003cp\u003eThe matching fastener is the \u003ca href=\"\/products\/orbot-screw-socket-new-latch\"\u003enew-style socket screw\u003c\/a\u003e.\u003c\/p\u003e\n\u003ch2\u003eIdentifying the right part\u003c\/h2\u003e\u003cp\u003eFasteners and small components change between production runs, and the part on your machine may not match the current drawing. Measure what you are replacing, or photograph it against a ruler, and send that with your model and serial number. It takes a minute and it saves an order that does not fit.\u003c\/p\u003e\n\u003chr\u003e\n\u003cp\u003eOrbot part numbers are not always obvious from the machine. Send us the model, the serial number and a photograph of the part you need and we will confirm it before you order.\u003c\/p\u003e","brand":"Orbot","offers":[{"title":"EACH","offer_id":43851480137941,"sku":"HOS1003-10","price":29.72,"currency_code":"AUD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/2179\/6391\/products\/Orbot-Latch-Retro-Kit-of-2.jpg?v=1780551466"},{"product_id":"orbot-grubscrew-hex-3-8inch-x-0-25inch-gr8","title":"Orbot Grubscrew Hex 3\/8in x 0.25in GR8","description":"\u003ch2\u003eOrbot hex grub screw, 3\/8 inch x 1\/4 inch, grade 8\u003c\/h2\u003e\n\u003cp\u003eA grade 8 hex socket grub screw from an Orbot machine.\u003c\/p\u003e\n\u003ch2\u003eGrade matters here\u003c\/h2\u003e\u003cp\u003eGrade 8 is a high tensile specification. Substituting a lower grade screw of the same size into a drive component is a false economy — it will hold until it does not, usually under load. Match the grade, not just the thread.\u003c\/p\u003e\n\u003ch2\u003eIdentifying the right part\u003c\/h2\u003e\u003cp\u003eFasteners and small components change between production runs, and the part on your machine may not match the current drawing. Measure what you are replacing, or photograph it against a ruler, and send that with your model and serial number. It takes a minute and it saves an order that does not fit.\u003c\/p\u003e\n\u003chr\u003e\n\u003cp\u003eOrbot part numbers are not always obvious from the machine. Send us the model, the serial number and a photograph of the part you need and we will confirm it before you order.\u003c\/p\u003e","brand":"Orbot","offers":[{"title":"EACH","offer_id":43851480826069,"sku":"HOSGRUBGR8","price":0.59,"currency_code":"AUD","in_stock":true}]},{"product_id":"orbot-grommet","title":"Orbot Grommet","description":"\u003ch2\u003eOrbot grommet\u003c\/h2\u003e\n\u003cp\u003eA rubber grommet from an Orbot machine.\u003c\/p\u003e\n\u003ch2\u003eSmall part, real job\u003c\/h2\u003e\u003cp\u003eGrommets protect a cable or a hose where it passes through a metal panel. A missing grommet lets the panel edge chafe the insulation, and on a wet machine that is how an electrical fault starts. Worth replacing on sight rather than at failure.\u003c\/p\u003e\n\u003ch2\u003eIdentifying the right part\u003c\/h2\u003e\u003cp\u003eFasteners and small components change between production runs, and the part on your machine may not match the current drawing. Measure what you are replacing, or photograph it against a ruler, and send that with your model and serial number. It takes a minute and it saves an order that does not fit.\u003c\/p\u003e\n\u003chr\u003e\n\u003cp\u003eOrbot part numbers are not always obvious from the machine. Send us the model, the serial number and a photograph of the part you need and we will confirm it before you order.\u003c\/p\u003e","brand":"Orbot","offers":[{"title":"EACH","offer_id":43851481022677,"sku":"HOS2010-02","price":149.6,"currency_code":"AUD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/2179\/6391\/products\/Orbot-Grommet.jpg?v=1780551467"},{"product_id":"orbot-drive-gear-micro","title":"Orbot Drive Gear Micro (Connects to Counterweight)","description":"\u003ch2\u003eOrbot Micro drive gear, connects to the counterweight\u003c\/h2\u003e\n\u003cp\u003eThe drive gear that connects to the counterweight on the Orbot Micro.\u003c\/p\u003e\n\u003ch2\u003eMicro-specific, and central to how the machine works\u003c\/h2\u003e\u003cp\u003eAn orbital machine is balanced by a counterweight running against the drive. If that connection wears, the machine loses its balance and the symptom is vibration and noise rather than loss of drive.\u003c\/p\u003e\u003cp\u003eThis gear is for the \u003cstrong\u003eOrbot Micro\u003c\/strong\u003e. Do not order it for a full-size machine.\u003c\/p\u003e\n\u003ch2\u003eIdentifying the right part\u003c\/h2\u003e\u003cp\u003eFasteners and small components change between production runs, and the part on your machine may not match the current drawing. Measure what you are replacing, or photograph it against a ruler, and send that with your model and serial number. It takes a minute and it saves an order that does not fit.\u003c\/p\u003e\n\u003chr\u003e\n\u003cp\u003eOrbot part numbers are not always obvious from the machine. Send us the model, the serial number and a photograph of the part you need and we will confirm it before you order.\u003c\/p\u003e","brand":"Orbot","offers":[{"title":"EACH","offer_id":43851481055445,"sku":"HOSDVGEARM","price":40.39,"currency_code":"AUD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/2179\/6391\/files\/Orbot-Drive-Gear-Micro-Connects-to-Counterweight.jpg?v=1780551467"},{"product_id":"orbot-damper-spray-cage","title":"Orbot Damper Spray Cage","description":"\u003ch2\u003eOrbot spray cage damper\u003c\/h2\u003e\n\u003cp\u003eThe damper from the spray cage assembly on an Orbot machine.\u003c\/p\u003e\n\u003ch2\u003eWhat a damper does on an orbital\u003c\/h2\u003e\u003cp\u003eAn orbital machine works by moving its head in a small, fast orbit. Everything mounted to that head is being shaken continuously, and dampers are what stop that vibration reaching the components. A perished damper transmits the vibration straight through, which is hard on fittings and unpleasant for the operator.\u003c\/p\u003e\n\u003ch2\u003eIdentifying the right part\u003c\/h2\u003e\u003cp\u003eFasteners and small components change between production runs, and the part on your machine may not match the current drawing. Measure what you are replacing, or photograph it against a ruler, and send that with your model and serial number. It takes a minute and it saves an order that does not fit.\u003c\/p\u003e\n\u003chr\u003e\n\u003cp\u003eOrbot part numbers are not always obvious from the machine. Send us the model, the serial number and a photograph of the part you need and we will confirm it before you order.\u003c\/p\u003e","brand":"Orbot","offers":[{"title":"EACH","offer_id":43851481252053,"sku":"HOS2023","price":3.41,"currency_code":"AUD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/2179\/6391\/products\/Orbot-Damper-Spray-Cage.jpg?v=1780551468"},{"product_id":"orbot-bolt-0-5inch-pull-latch-rod","title":"Orbot Bolt 0.5 Inch Pull Latch Rod","description":"\u003ch2\u003eOrbot bolt, 1\/2 inch, for the pull latch rod\u003c\/h2\u003e\n\u003cp\u003eThe bolt from the pull latch rod assembly on an Orbot machine.\u003c\/p\u003e\n\u003ch2\u003ePart of a small assembly\u003c\/h2\u003e\u003cp\u003eFitted with the \u003ca href=\"\/products\/orbot-nut-0-5inch-pull-latch-rod\"\u003enut\u003c\/a\u003e and the \u003ca href=\"\/products\/orbot-washer-0-5inch-nylon-pull-latch-r\"\u003enylon washer\u003c\/a\u003e in the same latch group.\u003c\/p\u003e\n\u003ch2\u003eIdentifying the right part\u003c\/h2\u003e\u003cp\u003eFasteners and small components change between production runs, and the part on your machine may not match the current drawing. Measure what you are replacing, or photograph it against a ruler, and send that with your model and serial number. It takes a minute and it saves an order that does not fit.\u003c\/p\u003e\n\u003chr\u003e\n\u003cp\u003eOrbot part numbers are not always obvious from the machine. Send us the model, the serial number and a photograph of the part you need and we will confirm it before you order.\u003c\/p\u003e","brand":"Orbot","offers":[{"title":"EACH","offer_id":43851482661077,"sku":"HOS1028","price":1.1,"currency_code":"AUD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/2179\/6391\/products\/Orbot-Bolt-0_5-Inch-Pull-Latch-Rod.jpg?v=1780551468"}],"url":"https:\/\/ccwonline.com.au\/collections\/orbot.oembed?page=2","provider":"Carpet Cleaners Warehouse","version":"1.0","type":"link"}